WELCOME
TO OUR STORE
EXCHANGER BOILER 300L WITH COIL STANDING GALMET
Gross
zł3,445.21
Sold: 2Gross
0/5
Anti-corrosion protection
The guarantee of safe use of hot water exchangers is to ensure the highest quality of anti-corrosion protection. The EXTRA GLASS® enamel used in GALMET heaters is ceramic enamel applied using the "wet" method, evenly over the entire surface of the exchanger. In addition, supported by two magnesium anodes is a guarantee of hygienic use.
Technical Specifications
Storage capacity (l) 309 (According to Commission Regulation (EU) 812/2013, 814/2013.)
ERP polyurethane foam B
Maximum operating temperature of the tank (deg. (C) 95
Maximum heat exchanger operating temperature (°C. C) 110
Maximum tank working pressure (MPa) 1
Maximum working pressure (MPa) 1,6
Exchanger area (m2): 1,4
Exchanger capacity (l) 9,8
Heat exchanger power (70/10/45°C) (kW) 33,6
Outside diameter (mm) 670
Height (mm) 1615
Net Weight (kg) 108
Share on:
Tower is a vertical exchanger that guarantees maximum use of the possibility of heating utility water by the central heating boiler. It allows you to store from 200 to 500 liters of water, which ensures comfortable use of domestic hot water by a large family.
Convenient installation
In the Tower heat exchanger, hydraulic connections are connected to the rear of the exchanger. This ensures convenient installation and facilitates daily operation. In the rear part there is also a for the sensor from the central heating boiler and a for connecting the circulation pump. After using the circulation pump in the DHW system, it is possible to immediately draw water at a constant temperature at any point of consumption. A large, legible thermometer is placed in the front part. To ensure the stability of the tank, each Tower exchanger is equipped with adjustable leveling feet.
Power
The spiral coil with a large surface area, located in the lower part of the tank, guarantees optimal use of the tank capacity. Connected to any central heating boiler or fireplace, it heats as much utility water as possible at a given time. The SGW(S) Tower exchanger can also be powered by an electric heater, installed with a GE electrical set or additional heaters installed on the flange, in the inspection hole. The use of a set of heaters on the flange provides quick access to domestic hot water, without the need to start the central heating boiler, e.g. in summer.
Proven insulation
The most efficient operation of the hot water exchanger is, in addition to the perfect coil, the merit of appropriate insulation. A thick layer of hard polyurethane insulation provides increased protection and thus long water temperature retention and low operating costs.
Anti-corrosion protection
The guarantee of safe use of hot water exchangers is to ensure the highest quality of anti-corrosion protection. The EXTRA GLASS® enamel used in GALMET heaters is ceramic enamel applied using the "wet" method, evenly over the entire surface of the exchanger. In addition, supported by two magnesium anodes is a guarantee of hygienic use.
Technical Specifications
Storage capacity (l) 309 (According to Commission Regulation (EU) 812/2013, 814/2013.)
ERP polyurethane foam B
Maximum operating temperature of the tank (deg. (C) 95
Maximum heat exchanger operating temperature (°C. C) 110
Maximum tank working pressure (MPa) 1
Maximum working pressure (MPa) 1,6
Exchanger area (m2): 1,4
Exchanger capacity (l) 9,8
Heat exchanger power (70/10/45°C) (kW) 33,6
Outside diameter (mm) 670
Height (mm) 1615
Net Weight (kg) 108
Specyfikacja
Status | New |
---|---|
Brand | GALMET |
Comments (0)
Your review appreciation cannot be sent
Report comment
Are you sure that you want to report this comment?
Report sent
Your report has been submitted and will be considered by a moderator.
Your report cannot be sent
Write your review
Review sent
Your comment has been submitted and will be available once approved by a moderator.
Your review cannot be sent